[Free] 2017(Oct) Dumps4cert Testinsides Cisco 400-151 Dumps with VCE and PDF Download 81-90

Dumps4Cert 2017 Oct Cisco Official New Released 400-151
100% Free Download! 100% Pass Guaranteed!

CCIE Data Center (v2.0)

Question No: 81

Refer to the exhibit.

Within an ACI fabric, a routing protocol is needed to assist with route redistribution between

the outside networks and the internal fabric. Which routing protocol is needed to run in the fabric at location 1 to allow the VM access to the networks advertised by the external Layer 3 network.

  1. eBGP

  2. OSPF

  3. MP-BGP

  4. iBGP

  5. IS-IS

Answer: C

Question No: 82 DRAG DROP

Drag and drop two configurations that should fail without data loss from the left column into the 2 Devices Lost column on the right.

Dumps4Cert 2017 PDF and VCE


Dumps4Cert 2017 PDF and VCE

Question No: 83 DRAG DROP

Drag and drop terms at the Cisco Prime Service Catalog from the left onto the definition on the right.

Dumps4Cert 2017 PDF and VCE


Dumps4Cert 2017 PDF and VCE

Explanation: Authorization persmissions

Review Requistion Service group

Question No: 84 DRAG DROP

Drag and drop feature on the left onto the appropriate business benefits on the right.

Dumps4Cert 2017 PDF and VCE


Dumps4Cert 2017 PDF and VCE



Data Center Bridging Exchange (DCBX) Protocol Fiber Channel over Ethernet (FCoE)


Ref:Cisco White Paper Data Center Bridging

Question No: 85

You configured a new appliance port, but the port has a pinning failure. Which option is possible cause?

  1. The appliance port admin speed must be adjusted.

  2. Appliance VLANs are missing duplicate global VLANs.

  3. The appliance is configured for NPV.

  4. Appliance VLANs are duplicated in global VLANs.

Answer: D

Question No: 86

Which Ether type is used to identify FIP?

A. 0x8914 B. 0x8906 C. 0x8915 D. 0x8905

Answer: A Explanation:

Ref:http://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus5000/sw/fcoe/513_n1_ 1/b_Cisco_n5k_fcoe_config_gd_re_513_n1_1/b_Cisco_n5k_fcoe_config_gd_re_513_n1_1


Question No: 87

Refer to the exhibit.

Dumps4Cert 2017 PDF and VCE

Which two statements are true? (Choose two.)

  1. Three pin groups are configured: one for the port-channel 10 in fabric interconnect B, one for int el/32 in fabric interconnect B, and one for int e1/31 in fabric interconnect B.

  2. Changing the target interface for an existing SAN pin group disrupts traffic for all vHBAs that use that pin group. The fabric interconnect performs a log in and log out for the Fibre Channel protocols to repin the traffic.

  3. To configure pinning for a server, you must include the SAN pin group in a vNIC policy. The vNIC policy is then included in the service profile assigned to that server. All traffic from the vNIC travels through the I/O module to the specified uplink Fibre channel port.

  4. In Fibre Channel switch mode, SAN pin groups are irrelevant. Any existing SAN pin groups are ignored.

  5. Edit this to show switch mode

Answer: B,D Explanation:

Ref: http://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/sw/gui/config/guide/1-0- 2/b_GUI_Config_Guide/GUI_Config_Guide_chapter19.html

Also see PDF: Configuring SAN Pin Groups

Question No: 88

Which option lists the valid roles for VSM?

  1. primary and secondary

  2. standalone, primary, and secondary

  3. central, primary, and secondary

  4. master and slave

Answer: B Explanation:

Ref:http://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus1000/sw/4_0/high_ava ilibility/configuration/guide/n1000v_ha/ha_3system.html

Question No: 89

Refer to the exhibit.

Dumps4Cert 2017 PDF and VCE

Corporate ABC wants to implement control by allowing authorized virtual machine MAC addresses to send traffic to the Internet. The administrator wants to add this MAC ACL on Nexus7k-1 to achieve the task

[Configuration Output] Nexus7k-1:

mac access-list mac-acl

permit 0050.561f.73d3 0000.00ff.ffff any


interface e1/1

mac access-group mac-acl

However, this action does not work. Which two statements describe the issue? (Choose two.)

  1. The MAC address and mask do not match.

  2. The MAC ACL cannot be applied to egress traffic.

  3. This command is wrong to apply this ACL under interface.

  4. The sequence number is missing from the ACL.

  5. The MAC ACL is not supported on Cisco nexus 7000 Series.

Answer: B,C Explanation:

Ref: http://www.cisco.com/c/en/us/td/docs/switches/datacenter/sw/4_1/nx- os/security/configuration/guide/sec_nx-os-cfg/sec_macacls.html

B is definitely correct as you can only apply a MAC ACLs to ingress traffic only

You can apply a MAC ACL as a port ACL to Layer 2, Layer 3, and Port-Channels but the command is as follows:

mac access-list acl-mac-01

permit 00c0.4f00.0000 0000.00ff.ffff any interface ethernet 2/1

mac port access-group acl-mac-01

Question No: 90

Refer to the exhibit.

Dumps4Cert 2017 PDF and VCE

Which outcome of this configuration is true?

  1. Any newly created traffic flows do not use this fabric interconnect.

  2. All traffic ceases to flow through this fabric interconnect after a reboot.

  3. Servers cease to use this fabric interconnect upon next reboot.

  4. All traffic ceases to flow through this fabric interconnect.

Answer: D

100% Dumps4cert Free Download!
Download Free Demo:400-151 Demo PDF
100% Dumps4cert Free Guaranteed!
Download 2017 Dumps4Cert 400-151 Dumps

Dumps4Cert ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

2017 Dumps4Cert IT Certification PDF and VCE

Add a Comment

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.